Hey, my name is Mindi, and I blog over at MyLove2Create, I am super happy to be here today!
I love repurposing and using free things to do a lot of my projects. You may remember when I updated a glass top coffee table with a pallet in July…well today I am using up some more of my free wood for a super fun and easy project. A DIY Triptych Frame.
Triptych: Pronounced Trip-tick, it is defined as: a picture or relief carving on three panels, typically hinged together side by side and used as an altarpiece, or, a set of three associated artistic, literary, or musical works intended to be appreciated together.
The idea of making a triptych frame came when I was contemplating a huge blank wall in my bedroom. It needed to be filled with something large. Since I am so indecisive I decided I wanted it to be something I could change up easily…
How to Build a Triptych Frame for Art Panels
You may have noticed I was cutting wood in the dark…a fun Friday night activity…when I have an idea I like to jump on it if I have the time, even if it is 9:00 pm. After cutting I came in and attached my frame to the beadboard, with glue and finish nails. I added the long sides which were the same length as the board, and then the ends. You can see I had a few rogue nails! Oops, nothing a little bending back and forth won’t solve, the nail will eventually break off. Then I called it a night.
I didn’t end up getting back to this project for a while, but when I did, I set to work looking in my stash for something to become my photo/art boards. I have had this bundle off chipboards for a while and realized they would work perfectly.
I cut three of them to a size that looked good on the frame…I didn’t really measure, just eyeballed it (dimensions below). Then found some scraps that would work for my picture holders. On the left you can see I was trying out the scraps to see if they would work. The white scraps were left over from a crib I turned into a dog crate. They were perfect because they were wider than the other scrap wood which would give me a place to slide my photo boards in and out.
On the right you can see I am marking on the photo board where I needed to line up the holders. I cut them to a random width that looked good on the board…but in hindsight I should have made them a little shorter, so the boards could slide in and out a little easier.
To attach the picture holders I needed to make sure the photo boards would be centered, and since I am lazy and prefer not to measure, if I can help it, I grabbed some scrap 1×4 boards to do the work for me.
I started on the ends and used a 1×4 to be my spacers (top left). I did have to trim a hair off of my photo boards to ensure all three 1×4’s fit, since I hadn’t thought of this measuring technique beforehand. Once they fit, I removed the bottom 1×4, and leaving the other spacers in place, I glued my smaller holder down, and then added the white holder on top. Then I nailed them to the beadboard at the same time. I repeated this for all of my picture holders.
*Note, you need to leave about an 1/8th of an inch wiggle room between the photo board and the picture holder, on the top and bottom, so that you have enough space to freely move the photo boards in and out of the frame.
Hopefully this will help as well. It is hard to see the widths on a few. The blue photo boards are 1/4 inch thick as well as the front white picture holders. The grey, back, picture holders are 1/2 inch thick.
When I put it in the frame I liked it a little better, the colors are fun at least. Now if you are an artist or are better at pretending than me, can you see how fun this would be? You could paint anything you want! Or if you don’t even want to go with painting at all, you could put family photos on the boards or try an engineering print like I did on the other side of my boards…
I got the largest print they had, and it was too big, of course. The first time I had ordered the middle size and it was too small, I will probably be doing a project with that print in the future. Anyway, I knew this print would be too big, but I didn’t realize the horse would be THAT big, so I had to cut him down…it adds character right?!
To cut it to size I pushed all three boards together and set the print on top. Then I felt the edges of the board under my print and placed my ruler on the very end of the board and cut the paper with and exacto knife. It was super easy and fast, and my print was the same size as the three boards. I love it when that happens.
I then took the board and print outside and used adhesive spray to do a light coat on the board and the back of the print. After waiting a minute (following the directions on the can) I carefully lined the top of the print to the top of the board, and used my hand to smooth it all the way down.