Since the beginning of Pinterest (which really wasn’t that long ago, but pre-Pinterest may as well be the age of the dinosaurs, ha!), there have been plenty of ideas that just go wild because they are so smart! One that I have seen over and over again is a utensil drawer organizer, with organizers turned vertically so that you can actually see all the utensils in the drawer. It’s everywhere because it’s brilliant, but typically the pictures are from a home show or builder’s website — and they are high-end upgrades for luxury homes, not found in older homes or the builder-grade homes that most of us live in. But, our brilliant guest today got the same look, for a fraction of the price — and it’s removable for easy cleaning, or if you decide you want to use the drawer for something else!
Ready to make your kitchen completely beautiful and functional and amazing while still staying true to your budget? You’re going to love Rachel’s utensil drawer organizer!
This post contains affiliate links for your convenience. See our full disclosure here.
How to Build an Upright Utensil Drawer Organizer
by Rachel Lynn from Queen Bee of Honey Dos
Hello Remodelaholics! This is Rachel Lynn from over at Queen Bee of Honey Dos, where I blog about all things home and garden. I am so very excited to be able to be with you all today, and to bring you one of my favorite DIY projects.
For those of you who do not yet know me, allow me just a few seconds to better introduce myself. I have an affinity for DIY projects, and the bigger the impact for the lowest budget that I can achieve, the better. I came into blogging after spending a few decades of remodeling and designing my own rooms and projects. I especially love creating furniture, either from scratch, or from old unused pieces that just need some love. (Like this beautiful sideboard)
As you can see from my kitchen, I am a drawer lover. In fact, this entire lower side of my kitchen has all drawers and pull-outs. Today, I am going to show you how I turned one of these deep drawers into a useable utensil storage space. So, let’s get right to it!
Because there are deep drawers on both sides of my cooktop, this is the best place to store all of the cooking utensils. However, I hate shuffling around through drawers, searching for a spatula or a spoon. I needed a solution, and I knew just what I wanted. I had seen something similar to this once during a kitchen showroom tour. I knew then that I would recreate what I saw at some point, and this seemed like as good a time as any. You’ll be surprised at how easy it was!
How to create this deep drawer utensil organizer
This is where the drawer is located in reference to my cooktop. And because I know from experience that some of you want to know the brands for the appliances, I will disclose that information to you now.
Those are Thermador Pro double ovens. The gas cooktop is also by Thermador. It is from their Pro line as well, and has the griddle center.
The cabinets came from Batesville Cabinets in Mississippi. ( I am not affiliated with either company in any way, and disclose this for informational purposes only). The design is my own.
Materials for this project
- (2) 2X 1/2″ strips cut to cabinet length
- 1/2″ sanded plywood or MDF cut to length and width for the inside of the drawer. (Leave 1/8″ on each side)
- Stainless steel utensil holders with lips. (These can easily be found at Amazon or Ebay).
- 1″ wood screws
- Jigsaw
- Drill
Step 1 – Measure
To get the placement for the ledger strips, measure the depth of the utensil holders, subtract the width of the ledger strips and the width of the plywood. For example: My holders are 5″ from the bottom to the lip, my plywood is 1/2″ thick and my ledgers are 1 3/4″ wide. So, 5 – (1/2 + 1 3/4) = 2 3/4. The bottom edge of the ledger strip will rest 2 3/4″ from the bottom of the drawer. Let’s round that off and make it an even 3.”
Step 2 – Attach ledger strips/supports
To attach the ledger strips, I will use a scrap piece of wood that is 3″ across as a spacer. This will help to keep it in place and level until the screws are inserted.
Step 3 – Attach supports
Next, pre drill a hole at each end of the ledger strip to prevent splitting. Then, insert a 1″ screw into each hole. Repeat the process for the opposite side of the drawer.
Step 4 – Determine utensil holder placement
Trace the outline of the utensil holders onto the plywood in the layout that is desirable. On mine, I evenly distributed all six stainless steel holders.
Step 5 – Cut
Drill a starting hole for each circle and then, use a jigsaw to cut the opening for the holders. When, making the cut stay about 1/4″ on the inside of the traced line so that the edge of the holders have a ledge to rest. Test the holders for fit.
Tip: when using a jigsaw, place the visible side of the wood down so that any splintering will not be seen.
This is the back side of my wood after all six holes have been cut. As you can see, the holes do not have to be perfect, and thank goodness for that. 
Walang komento:
Mag-post ng isang Komento